Dyno Tuning
We have a Dimsport Dynorace 1000hp 4 wheel drive inertia system rolling road, this can test all four and
two wheel drive vehicles up to 1000hp.
If you decide to have your car tuned on the dyno it will involve us strapping your car onto the dyno via the
chassis with heavy duty car straps, once the vehicle is secure we will then run the car engine up to normal
operating temperature in preparation for the dyno run.
To test the cars current horse power and torque settings we will select the correct gear and run the engine
to full load for a few short seconds and then let the vehicle freewheel so the dyno can make all the
calculations that is required to display the correct information on screen, we will then repeat this test
around three times to get an average reading.
After we have performed the remap and uploaded it back into your vehicle we will then run the car again
and if needed we will make any final adjustments that are required until we are happy with the end results,
this will then complete the dyno test, you will then receive a printout of the dyno test and it will show you
the results of the pre runs and of the tuned runs, thus giving the increases made during the remap.
Please be aware that if you are wanting your vehicle tuned on our dyno that there could be a wait of at
least four weeks as we constantly use it for file development as we are now mainly a file providing service
for the agents of Custom Tuning.
Dyno Tuning
We have a Dimsport Dynorace 1000hp 4 wheel drive inertia system rolling
road, this can test all four and two wheel drive vehicles up to 1000hp.
If you decide to have your car tuned on the dyno it will involve us strapping your
car onto the dyno via the chassis with heavy duty car straps, once the vehicle is
secure we will then run the car engine up to normal operating temperature in
preparation for the dyno run.
To test the cars current horse power and torque settings we will select the
correct gear and run the engine to full load for a few short seconds and then let
the vehicle freewheel so the dyno can make all the calculations that is required
to display the correct information on screen, we will then repeat this test around
three times to get an average reading.
After we have performed the remap and uploaded it back into your vehicle we
will then run the car again and if needed we will make any final adjustments
that are required until we are happy with the end results, this will then complete
the dyno test, you will then receive a printout of the dyno test and it will show
you the results of the pre runs and of the tuned runs, thus giving the increases
made during the remap.
Please be aware that if you are wanting your vehicle tuned on our dyno that
there could be a wait of at least four weeks as we constantly use it for file
development as we are now mainly a file providing service for the agents of
Custom Tuning.
Dyno Tuning
We have a Dimsport Dynorace 1000hp 4 wheel drive inertia
system rolling road, this can test all four and two wheel drive
vehicles up to 1000hp.
If you decide to have your car tuned on the dyno it will
involve us strapping your car onto the dyno via the chassis
with heavy duty car straps, once the vehicle is secure we will
then run the car engine up to normal operating temperature
in preparation for the dyno run.
To test the cars current horse power and torque settings we
will select the correct gear and run the engine to full load for
a few short seconds and then let the vehicle freewheel so the
dyno can make all the calculations that is required to display
the correct information on screen, we will then repeat this test
around three times to get an average reading.
After we have performed the remap and uploaded it back into
your vehicle we will then run the car again and if needed we
will make any final adjustments that are required until we are
happy with the end results, this will then complete the dyno
test, you will then receive a printout of the dyno test and it will
show you the results of the pre runs and of the tuned runs,
thus giving the increases made during the remap.
Please be aware that if you are wanting your vehicle tuned
on our dyno that there could be a wait of at least four weeks
as we constantly use it for file development as we are now
mainly a file providing service for the agents of Custom
Tuning.
Dyno Tuning
We have a Dimsport Dynorace 1000hp 4 wheel
drive inertia system rolling road, this can test all
four and two wheel drive vehicles up to 1000hp.
If you decide to have your car tuned on the dyno
it will involve us strapping your car onto the dyno
via the chassis with heavy duty car straps, once
the vehicle is secure we will then run the car
engine up to normal operating temperature in
preparation for the dyno run.
To test the cars current horse power and torque
settings we will select the correct gear and run
the engine to full load for a few short seconds
and then let the vehicle freewheel so the dyno
can make all the calculations that is required to
display the correct information on screen, we will
then repeat this test around three times to get an
average reading.
After we have performed the remap and
uploaded it back into your vehicle we will then
run the car again and if needed we will make
any final adjustments that are required until we
are happy with the end results, this will then
complete the dyno test, you will then receive a
printout of the dyno test and it will show you the
results of the pre runs and of the tuned runs,
thus giving the increases made during the
remap.
Please be aware that if you are wanting your
vehicle tuned on our dyno that there could be a
wait of at least four weeks as we constantly use
it for file development as we are now mainly a
file providing service for the agents of Custom
Tuning.
Dyno Tuning
We have a Dimsport Dynorace 1000hp
4 wheel drive inertia system rolling
road, this can test all four and two
wheel drive vehicles up to 1000hp.
If you decide to have your car tuned on
the dyno it will involve us strapping your
car onto the dyno via the chassis with
heavy duty car straps, once the vehicle
is secure we will then run the car engine
up to normal operating temperature in
preparation for the dyno run.
To test the cars current horse power
and torque settings we will select the
correct gear and run the engine to full
load for a few short seconds and then
let the vehicle freewheel so the dyno
can make all the calculations that is
required to display the correct
information on screen, we will then
repeat this test around three times to
get an average reading.
After we have performed the remap and
uploaded it back into your vehicle we
will then run the car again and if needed
we will make any final adjustments that
are required until we are happy with the
end results, this will then complete the
dyno test, you will then receive a
printout of the dyno test and it will show
you the results of the pre runs and of
the tuned runs, thus giving the
increases made during the remap.
Please be aware that if you are wanting
your vehicle tuned on our dyno that
there could be a wait of at least four
weeks as we constantly use it for file
development as we are now mainly a
file providing service for the agents of
Custom Tuning.
Dyno Tuning
We have a Dimsport Dynorace
1000hp 4 wheel drive inertia system
rolling road, this can test all four and
two wheel drive vehicles up to
1000hp.
If you decide to have your car tuned
on the dyno it will involve us
strapping your car onto the dyno via
the chassis with heavy duty car
straps, once the vehicle is secure we
will then run the car engine up to
normal operating temperature in
preparation for the dyno run.
To test the cars current horse power
and torque settings we will select the
correct gear and run the engine to full
load for a few short seconds and then
let the vehicle freewheel so the dyno
can make all the calculations that is
required to display the correct
information on screen, we will then
repeat this test around three times to
get an average reading.
After we have performed the remap
and uploaded it back into your
vehicle we will then run the car again
and if needed we will make any final
adjustments that are required until we
are happy with the end results, this
will then complete the dyno test, you
will then receive a printout of the
dyno test and it will show you the
results of the pre runs and of the
tuned runs, thus giving the increases
made during the remap.
Please be aware that if you are
wanting your vehicle tuned on our
dyno that there could be a wait of at
least four weeks as we constantly
use it for file development as we are
now mainly a file providing service for
the agents of Custom Tuning.
